Splash Guards for Renault Captur (2013-2020)
Engineered to match the Renault Captur B-segment crossover, these mud flaps provide wheel-arch protection tailored to both the J87 1st-Generation platform (2013-2018) and the JB/JE 2nd-Generation CMF-B platform (2019-2020). The Captur ranks among Europe's best-selling subcompact SUVs, with over 1.2 million first-generation units sold worldwide.
J87 (2013-2018): B-platform shared with Renault Clio IV and Nissan Juke F15. Produced at Renault Valladolid, Spain. Sold in South Korea as Renault Samsung QM3 with identical body dimensions and wheel-arch geometry.
JB/JE (2019-2020): CMF-B platform shared with Renault Clio V and Nissan Juke F16. Larger body with revised wheel-arch contours compared to J87.
Why Vehicle-Specific Flaps Matter
Each generation's wheel-arch geometry differs due to platform changes from B to CMF-B. Universal mud flaps leave gaps that allow debris to reach the sill and door panels. These Captur-specific flaps align with factory mounting points for a gap-free seal across both generations.
Product Specifications
Material and Construction
Hardware Included
OEM Material Options
Available in multiple material grades upon request:
PP (standard production)
PP+TPE (enhanced flexibility for cold climates)
TPE (premium thermoplastic elastomer)
ABS (rigid option for heavy-duty use)
Vehicle Fitment Guide
Covered Variants
2013-2018 Renault Captur (J87, 1st Gen): European market, pre-facelift and facelift (2017+). All trims: Expression, Expression+, Dynamique, Signature, Iconic, S-Edition.
2013-2019 Renault Samsung QM3 (J87K): South Korean market rebadge with identical body dimensions. Pre-facelift (PH1, 2013-2017) and New QM3 facelift (PH2, 2017-2019).
2019-2020 Renault Captur (JB/JE, 2nd Gen): European market, CMF-B platform. Sold in South Korea as Renault Captur from 2020 (no longer QM3 badge).
Not Covered
The following nameplates share the Captur family name but are built on a different platform (B0 / Dacia Duster) with different body dimensions. These mud flaps will NOT fit:
Renault Kaptur (2016-2022): Russian and CIS market, B0 platform
Renault Captur Global Access (2016-2023): India, Brazil, emerging markets, B0 platform
Renault Grand Captur: Uruguay market variant of Global Access, B0 platform
Mitsubishi ASX (2023-present): Rebadged 2nd-gen Captur on CMF-B platform. May share mud flap compatibility with JB/JE Captur, but falls outside this SKU's 2013-2020 year range. Buyers should verify fitment separately.
Installation Guide
Allen hex key (included in hardware kit)
Flathead screwdriver (for clip removal)
Torque wrench (recommended for precise tightening)
Installation Steps
Clean the wheel-arch edge and fender liner area with degreaser to ensure proper clip adhesion.
Position the front mud flap against the wheel-arch contour. Align mounting holes with factory fender clips.
Insert plastic fender fastener clips into the alignment holes. Press firmly until fully seated.
Secure lower mounting points with U-clip screws.
Tighten Allen screws using the included hex key. Do not overtighten to avoid cracking the PP material.
Repeat for the rear mud flaps, noting the different contour for rear wheel-arch geometry.
Verify all fasteners are secure. Test by hand for any movement or gaps.
J87 vs JB/JE Mounting Notes
The 2nd-Generation JB/JE Captur has a revised wheel-arch profile due to the CMF-B platform change. Ensure the correct flap orientation is selected for your generation before tightening fasteners. The J87 and JB/JE mounting point locations differ slightly at the lower fender edge.