Suzuki Every, Suzuki Carry
Universal
100 sets
FOB, CIF
T/T, L/C, Credit Card, Western Union
USD, EUR, HKD
Suzuki Every, Suzuki Carry, Suzuki Multicab, Suzuki Transform, Mazda Scrum, Nissan NV100 Clipper, Nissan Clipper Rio, Mitsubishi Minicab, Mitsubishi Town Box
2005-2015, 2015-Present
Suspension Arm
Front Suspension Parts Set, Lower Control Arm Set, Sway Bar Link Set, Front Lower Arm Pair, Steering Link Set, Suspension Rebuild Parts
| Suspension Part Type: | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Fitment: | |||||||||
| SKU: | |||||||||
| Availability: | |||||||||
| Quantity: | |||||||||
| |||||||||
This front suspension parts set covers the two wear parts that decide how a kei van behaves: the front stabilizer link and the front lower arm, also listed as the sway bar link and the lower control arm. The family is built for the 2005-2015 Suzuki Every DA64, the 2015-Present Every DA17 and the Suzuki Carry platforms, and every combination is quoted against the original Suzuki part number so the order matches the number stamped on the part being replaced. The stabilizer link is supplied as a left and right pair under 42420-68H00, the same number for the DA64 and the DA17. The lower arm is also a left and right pair, in five separate versions, because the DA64, the DA17, the F6A Carry, the K6A Carry and the 12 mm hole version each use a different original number. Per the source listing, Road Traffic is Universal, so one part serves left-hand-drive and right-hand-drive vehicles. Quote the vehicle and the part number, the five lower arm versions are not interchangeable.
A kei van carries its load low and close to the wheel, so every pothole and every load shift works through the front suspension. When the link bushings crack or the ball joint wears, the van starts to wander, the steering wheel shakes under braking, and the noise from under the bonnet turns into a repair bill. Replacing the same parts as a pair is the usual workshop practice, and keeping the numbers on record is what makes the next order fast.
Front stabilizer link: the short rod between the stabilizer bar and the strut, sold as a left and right pair under 42420-68H00, the same number for the DA64 and the DA17
Front lower arm, 68H00 series: the factory arm for the DA64 and for the Carry DA65T, left 45202-68H00 and right 45201-68H00
Front lower arm, 64P00 series: the factory arm for the DA17, left 45202-64P00 and right 45201-64P00
Front lower arm, 77A10 series: the F6A Carry arm for the DA52 and DA62 platforms, left 45202-77A10 and right 45201-77A10
Front lower arm, 82J01 12 mm hole: the version with the wider bracket hole, fitted to the Transform retrofit line rather than to the factory DA64
Each version was developed for a different chassis and a different supplier, and the original numbers do not cross over between them
Quoting the number on the arm already fitted removes any guesswork about which of the versions the vehicle takes
Mixing versions is not possible, the 68H00, 64P00, 77A10 and 82J01 arms do not share a mounting point
The stabilizer link carries the load from the stabilizer bar into the strut, and it is the part that lets the bar resist body roll in a turn
The lower arm locates the front wheel and carries the braking and steering load through the ball joint
Together they set the front wheel alignment, which is why worn parts show up as a wandering vehicle and not only as noise
Both parts are wear items rather than accident items, and they are normally replaced as a pair
Yes, the two part types sit in the same product family and can be quoted on one order quantity
State the vehicle and the part number for each line, the fitment and the part type are separate selections
Set packing by vehicle is available, so a workshop can order a complete front suspension rebuild for one vehicle in one carton
Each combination of part type and fitment is a separate item with its own original number and its own set contents. The dimensions and thread details below are taken from the original catalogue and from the filter and arm manufacturers, and small differences between production batches are normal.
Front stabilizer link, also called sway bar link, supplied as a left and right pair
Replaces Suzuki 42420-68H00 and 42420-68H01
Set contents: 2 links and 4 self-locking nuts
Pressed steel body with a rubber boot over the ball joint
Weight: approximately 0.6 kg per pair
68H00 series, for the DA64 and the Carry DA65T: left 45202-68H00, 45202-68H01, 45202-68H02, 45202-68H03, right 45201-68H00, 45201-68H01, 45201-68H02, 45201-68H03
64P00 series, for the DA17: left 45202-64P00, right 45201-64P00
77A10 series, for the F6A Carry DA52 and DA62: left 45202-77A10 and 45202-77A01, right 45201-77A10 and 45201-77A01
82J01 12 mm hole version, for the Transform retrofit line: left 45202-82J01, right 45201-82J01
Type: forged or stamped steel arm carrying a pressed ball joint, the ball joint is not separately replaceable on the factory arm
Set contents: 1 left arm and 1 right arm, and the set should be fitted as a pair to hold the alignment
Each combination is quoted under its own article code. State the code when placing the order, or pick the part type and the fitment in the two menus and the code is filled in automatically.
SKU Code | Part Type | Fitment | Replaces OE |
|---|---|---|---|
SUS-LA77-SUZCAR-9807 | Lower Arm 77A10 Series | 1998-2007 Carry (DA52/DA62 F6A) | 45201-77A10 |
SUS-SL-SUZEVE64-0515 | Stabilizer Link | 2005-2015 Every (DA64) | 42420-68H00 |
SUS-LA68-SUZEVE64-0515 | Lower Arm 68H00 Series | 2005-2015 Every (DA64) | 45201-68H00 |
SUS-LA82-SUZEVE64W-0712 | Lower Arm 82J01 12 mm Hole | 2007-2012 Every / Transform (DA64W, 12 mm Hole) | 45201-82J01 |
SUS-LA68-SUZCAR-1399 | Lower Arm 68H00 Series | 2013-Present Carry (DA65T) | 45201-68H00 |
SUS-SL-SUZEVE17-1599 | Stabilizer Link | 2015-Present Every (DA17) | 42420-68H00 |
SUS-LA64-SUZEVE17-1599 | Lower Arm 64P00 Series | 2015-Present Every (DA17) | 45201-64P00 |
Read the number on the part being replaced, that single check decides all five lower arm versions
Confirm the side, the left arm and the right arm carry different numbers on every version in this family
For the 12 mm hole version, measure the bracket hole on the existing arm before ordering
Replace the stabilizer link as a pair, and fit the lower arms as a pair, so the front alignment holds after the work
Seven combinations are available across the part types and the vehicle platforms. The table lists the Suzuki original number for each combination together with the numbers used on the rebadged Nissan, Mazda and Mitsubishi versions, so an order can be placed from whichever number appears on the part already fitted to the vehicle.
Part Type | Fitment | Suzuki OE | Cross Reference Numbers |
|---|---|---|---|
Stabilizer Link | 2005-2015 Every (DA64) | 42420-68H00 | Mazda 1A04-34-150, Nissan 54616-4A00D |
Stabilizer Link | 2015-Present Every (DA17) | 42420-68H00 | Mazda 1A04-34-150, Nissan 54616-4A00D |
Lower Arm 68H00 Series | 2005-2015 Every (DA64) | 45201-68H00 | Left 45202-68H00, Mazda 1A09-34-300 |
Lower Arm 68H00 Series | 2013-Present Carry (DA65T) | 45201-68H00 | Left 45202-68H00, Mazda 1A09-34-300 |
Lower Arm 64P00 Series | 2015-Present Every (DA17) | 45201-64P00 | Left 45202-64P00, Nissan 54616-4A00D |
Lower Arm 77A10 Series | 1998-2007 Carry (DA52/DA62 F6A) | 45201-77A10 | Left 45202-77A10, Mazda 1A04-34-350 |
Lower Arm 82J01 12 mm Hole | 2007-2012 Every / Transform (DA64W, 12 mm Hole) | 45201-82J01 | Left 45202-82J01, Nissan 54501-4A00A |
No, it is a separate version with a wider bracket hole, and it is not the factory fitting for the DA64V or DA64W
The factory arm for the DA64 is the 68H00 series, and the 12 mm hole version belongs to the Transform retrofit line, which uses the DA64W platform
Measure the hole on the existing arm, or read the number on it, before choosing between the 68H00 and the 82J01 versions
The 82J01 version also cross-references 45202-64P00, so a vehicle that carries that number needs the arm matched to it rather than to the vehicle name
Read the number stamped on the arm or link being replaced, that decides the version in one step
For the lower arm, check the side, the left and right arms carry different numbers in every version
Send the chassis code and a photo of the old part for a fitment check before a bulk order
Other Suzuki models and other kei vans, the arms and links are shaped for the Every and Carry mounting points
Older Every generations before the DA64 platform, the arm and link design changed
Any vehicle whose old part carries a number not listed in the table above
Will these suspension parts fit my Suzuki Every?
Yes, this family covers the 2005-2015 Every DA64, the 2015-Present Every DA17 and the Suzuki Carry platforms, and each combination is quoted against the original Suzuki number. The stabilizer link is the same part on the DA64 and the DA17 under 42420-68H00, while the lower arm has five separate versions, so read the number on the arm already fitted to the vehicle before ordering. Send the chassis code and a photo of the old part for a fitment check before a bulk order.
Which lower arm does my Every take?
It depends on the number on the arm already fitted, and the vehicle name alone is not enough. The DA64 and the Carry DA65T take the 68H00 series, the DA17 takes the 64P00 series, the F6A Carry DA52 and DA62 take the 77A10 series, and the Transform 12 mm hole version takes the 82J01. Quote that number with the order and the matching version is supplied.
Can I order the stabilizer link and the lower arms together?
Yes, both part types sit in the same product family and can be quoted on one order quantity. Select the part type and the fitment for each line in the two menus, and state the vehicle and the part number for each line. Set packing by vehicle is also available for a complete front suspension rebuild in one carton.
Are the parts supplied as left and right pairs?
Yes. The stabilizer link is a left and right pair with the four self-locking nuts included, and the lower arm is supplied as one left and one right arm with the side marked on each piece. The left and right arms carry different original numbers in every version, which is why they are not ordered as single pieces.
Can the ball joint be replaced separately?
No, on the factory arm the ball joint is pressed in and is not separately replaceable, so the arm assembly is the service unit. Ordering the arm as a pair also keeps the front alignment within tolerance after the work, and replacing one side only is what usually brings the vehicle back for a second visit.
How long do these parts last?
They are wear items rather than accident items, and the useful life depends on the road, the load and the general condition of the vehicle rather than on a fixed number of years. On a kei van that carries its load low and close to the wheel, the bushings and the ball joint take a steady load from every load shift, so checking them during a routine service is the practical approach. Ask the workshop that fits the parts for a condition-based replacement plan for the vehicle in front of you.
Will they fit a 2026 facelift Every?
The suspension parts sit inside the wheel arch and are not affected by the front end change, but the platform is badged DA18 in some markets from 2026, so check the chassis code on the vehicle and read the number on the old arm rather than relying on the model year alone. The numbers on the table are the deciding factor for every combination in this family.
What should the workshop check before fitting?
Read the number on the part being replaced, confirm the side, and measure the bracket hole on the existing arm if the 12 mm hole version is being considered. The stabilizer link and the lower arm are normally replaced as pairs, and the wheel alignment should be checked after the work, because the arm sets the front wheel position. Fitment support is not provided with the parts, so the installation should be done by a workshop that can check the alignment afterwards.
Suspension parts are machined and forged steel with a pressed ball joint, and they travel to humid markets where the packaging decides whether the part arrives fit for service. Every set is bagged, oiled against surface rust and boxed, and the arm sets are packed so the ball joint and the bushing faces are not loaded in transit. Because a workshop rebuilding one vehicle needs both part types, the sets are also packed by vehicle.
Each arm and each link is wrapped individually and boxed, the ball joint and bushing faces are protected
Anti-rust oil and a corrosion inhibitor paper are applied before packing, the parts are shipped for long sea routes and humid storage
Left and right pieces are labelled separately, and the original part number is printed on the label
Each article code is printed on the carton label next to the part number, so the code and the part can be checked against each other on arrival
Neutral export packing as standard, branded packing on request
A stabilizer link pair and a lower arm pair for one vehicle can be packed in a single set carton, this is the format most workshops order
Set cartons are labelled by vehicle rather than by part type, so a workshop can pick the right set for a vehicle in one movement
State the split between full sets and single part types at quotation
MOQ: 100 sets
Delivery terms: FOB, CIF
Payment: T/T, L/C, Credit Card, Western Union
Currencies: USD, EUR, HKD
Arm sets are heavier than the link pairs, so a mixed shipment carries the link pairs as the compact part and the arm sets as the dense part
Keep the cartons dry and out of direct sunlight in store, and open the individual wrapping as late as possible so the anti-rust protection stays on the part
All seven valid combinations can be mixed within one order quantity
Auto parts are essential components for the proper functioning of vehicles used in car assembly lines or for maintenance and repair services after purchase. Autobridge™ (Xiamen) provides a wide range of OES, aftermarket replacement parts, including AC compressors, cylinder heads, oil pumps, power steering pumps, starter motors, and turbochargers. These components are installed in powertrains, steering systems, rear axle assemblies, and chassis assemblies. Auto parts need to meet the design specifications and performance requirements of the original equipment manufacturer (OEM) parts, as well as comply with local regulations or CAPA certification. Depending on the requirements based on OEMs (Original Equipment Manufacturers) for material or design improvements, aftermarket parts may outperform the original genuine parts.
Car accessories are AFTERMARKET MODIFIED PARTS for cars after the production line. Autobridge™ (Xiamen) offers a variety of accessories, including an airflow snorkel, bumper, door visors, matting, spoiler, and trunk tray. The car accessories are not performance parts and generally do not affect the original power and safety. They are used to modify the appearance style, enhance off-road capabilities, or increase driving comfort. Compared to the genuine accessories, we offer customization services for aftermarket replacement accessories that cater to the buyer's specific requirements. Each accessory can be designed specifically for different car models.
Jaecoo is Chery's SUV brand built only for overseas buyers. This piece examines why it was created, how its J5–J8 models carry the "elegant off-road" idea, and what its UK and Southeast Asia sales truly show. It covers the "Temu Range Rover" joke, the SHS hybrid that suits weak charging networks, and a clear-eyed verdict: Jaecoo has proved it can get hot — but not yet that it can stay.
Read More
